Bush Insider Who Planned To Tell All Killed

Bush Insider Who Planned To Tell All Killed In Plane CrashFederal Investigation



Flashback: Rove Threatened GOP IT Guru If He Does Not ‘Take the Fall’ for Election Fraud in Ohio, Says Attorney

Michael Connell, the Bush IT expert who has been directly implicated in the rigging of George Bush’s 2000 and 2004 elections, was killed last night when his single engine plane crashed three miles short of the Akron airport. Velvet Revolution (”VR”), a non-profit that has been investigating Mr. Connell’s activities for the past two years, can now reveal that a person close to Mr. Connell has recently been discussing with a VR investigator how he can tell all about his work for George Bush. Mr. Connell told a close associate that he was afraid that George Bush and Dick Cheney would “throw [him] under the bus.”



A tipster close to the McCain campaign disclosed to VR in July that Mr. Connell’s life was in jeopardy and that Karl Rove had threatened him and his wife, Heather. VR’s attorney, Cliff Arnebeck, notified the United States Attorney General , Ohio law enforcement and the federal court about these threats and insisted that Mr. Connell be placed in protective custody. VR also told a close associate of Mr. Connell’s not to fly his plane because of another tip that the plane could be sabotaged. Mr. Connell, a very experienced pilot, has had to abandon at least two flights in the past two months because of suspicious problems with his plane. On December 18, 2008, Mr. Connell flew to a small airport outside of Washington DC to meet some people. It was on his return flight the next day that he crashed.



On October 31, Mr. Connell appeared before a federal judge in Ohio after being subpoenaed in a federal lawsuit investigating the rigging of the 2004 election under the direction of Karl Rove. The judge ordered Mr. Connell to testify under oath at a deposition on November 3rd, the day before the presidential election. Velvet Revolution received confidential information that the White House was extremely concerned about Mr. Connell talking about his illegal work for the White House and two Bush/Cheney 04 attorneys were dispatched to represent him.



An associate of Mr. Connell’s told VR that Mr. Connell was involved with the destruction of the White House emails and the setting up of the off-grid White House email system.



Mr. Connell handled all of John McCain’s computer work in the recent presidential campaign. VR has received direct evidence that the McCain campaign kept abreast of the legal developments against Mr. Connell by reading the VR dedicated website, www.rovecybergate.com.



VR demands that the Ohio Attorney General and the United States Justice Department conduct a complete investigation into the activities of Mr. Connell and determine whether there was any foul play in his death. VR demands that federal law enforcement officials place the following people under protective custody pending this investigation. Heather Connell who is the owner of GovTech Solutions, Randy Cole, the former President of GovTech Solutions, and Jeff Averbeck, the CEO of SmartTech in Chattanooga, Tennessee. Both GovTech and SmartTech have been implicated in the rigging of the 2000 and 2004 elections and the White House email scandal.



Our prior request to have Mr. Connell protected went unheeded and now he is dead.

Views: 49

Comment

You need to be a member of 12160 Social Network to add comments!

Join 12160 Social Network

"Destroying the New World Order"

TOP CONTENT THIS WEEK

THANK YOU FOR SUPPORTING THE SITE!

mobile page

12160.info/m

12160 Administrators

 

Latest Activity

Sandy posted photos
2 minutes ago
Doc Vega posted blog posts
23 hours ago
Sandy posted a photo
yesterday
Doc Vega posted photos
yesterday
cheeki kea favorited tjdavis's video
yesterday
cheeki kea commented on Doc Vega's photo
yesterday
Doc Vega posted blog posts
Friday
Doc Vega posted a photo
Wednesday
Doc Vega posted blog posts
Wednesday
Doc Vega posted a blog post

How they Planned the Destruction of America (And Nearly Succeeded)

In 2020 The Democrats went on a major offensive. Prevent Donald Trump from taking office, continue…See More
Tuesday
Doc Vega posted blog posts
May 31
Doc Vega posted a photo
May 31
Sandy posted a photo
May 31
tjdavis posted a video

It's Over. The Tool Bans Just Arrived!

First tool ban is here! A new law was just signed in New York that requires blueprint blocking technology on every CNC machine, laser cutter, lathe and 3D pr...
May 30
tjdavis posted photos
May 30
Doc Vega posted a blog post

Angry Old Man James Carville Warns of More to Come?

 A new type of signaling is brewing among the left and disenfranchised Democrats who have refused…See More
May 30
Doc Vega posted photos
May 29
Sandy posted photos
May 29
Sandy posted videos
May 29
Doc Vega posted blog posts
May 29

© 2026   Created by truth.   Powered by

Badges  |  Report an Issue  |  Terms of Service

content and site copyright 12160.info 2007-2019 - all rights reserved. unless otherwise noted